Mô tả sản phẩm

HG-SR702J+MR-J4-700A 26A 7KW 33.4NM 2000RPM OIL SEAL AC SERVO MOTOR DRIVE KIT WITH 3M CABLE NEW

MOTOR SPECIFICATIONS:

SERVO MOTOR MODEL HG-SR_		52(B)	102(B)	152(B)	202(B)	352(B)	502(B)	702(B)
POWER FACILITY CAPACITY [KVA]		1.0	1.7	2.5	3.5	5.5	7.5	10
CONTINUOUS RUNNING DUTY	RATED OUTPUT [KW]	0.5	1.0	1.5	2.0	3.5	5.0	7.0
CONTINUOUS RUNNING DUTY	RATED TORQUE [NM]	2.4	4.8	7.2	9.5	16.7	23.9	33.4
MAXIMUM TORQUE [NM]		7.2	14.3	21.5	28.6	50.1	71.6	1000
RATED ROTATION SPEED		2000[RPM]
MAXIMUM ROTATION SPEED		3000[RPM]
PERMISSIBLE INSTANTANEOUS ROTATION SPEED		3450[RPM]
RATED CURRENT [A]		2.9	5.6	9.4	9.6	14	22	26
MAXIMUM CURRENT [A]		9.0	17.4	29.1	30.7	44.8	70.4	83.2
WEIGHT [KG]		4.8	6.2	7.3	11	16	20	27
WEIGHT [KG]( WITH BRAKE)		6.7	8.2	9.3	17	22	26	33

DRIVE SPECIFICATIONS:

MODE NAME		MR-J4-700A
STOCKED ITEM		S
OUTPUT	RATED VOLTAGE	3-PHASE 170 VAC
OUTPUT	RATED CURRENT (A)	37.0
MAIN CIRCUIT POWER SUPPLY	VOLTAGE/FREQUENCY	3-PHASE 200 VAC TO 240 VAC, 50/60 HZ
	RATED CURRENT (A)	28.9
	PERMISSIBLE VOLTAGE FLUCTUATION	3-PHASE 170 VAC TO 264 VAC
	PERMISSIBLE FREQUENCY FLUCTUATION	±5% MAXIMUM
CONTROL CIRCUIT POWER SUPPLY	VOLTAGE/FREQUENCY	1-PHASE 200 VAC TO 240 VAC, 50/60 HZ
	RATED CURRENT (A)	0.3
	PERMISSIBLE VOLTAGE FLUCTUATION	1-PHASE 170 VAC TO 264 VAC
	PERMISSIBLE FREQUENCY FLUCTUATION	±5% MAXIMUM
	POWER CONSUMPTION (W)	45
INTERFACE POWER SUPPLY		24 VDC ±10% (REQUIRED CURRENT CAPACITY: 0.5 A (INCLUDING CN8 CONNECTOR SIGNAL))
LOAD-SIDE ENCODER INTERFACE		MITSUBISHI HIGH-SPEED SERIAL COMMUNICATION
TOLERABLE REGENERATIVE POWER OF THE BUILT-IN REGENERATIVE RESISTOR(W)		170
CONTROL METHOD		SINE-WAVE PWM CONTROL/CURRENT CONTROL METHOD
DYNAMIC BRAKE		BUILT-IN
PROTECTIVE FUNCTIONS		OVERCURRENT SHUT-OFF, REGENERATIVE OVERVOLTAGE SHUT-OFF, OVERLOAD SHUT-OFF (ELECTRONIC THERMAL), SERVO MOTOR OVERHEAT PROTECTION,ENCODER ERROR PROTECTION, REGENERATIVE ERROR PROTECTION, UNDERVOLTAGE PROTECTION, INSTANTANEOUS POWER FAILURE PROTECTION, OVER-SPEED PROTECTION, ERROR EXCESSIVE PROTECTION, MAGNETIC POLE DETECTION PROTECTION, LINEAR SERVO CONTROL FAULT PROTECTION
POSITION CONTROL MODE	MAXIMUM INPUT PULSE FREQUENCY	4 MPPS (WHEN USING DIFFERENTIAL RECEIVER), 200 KPPS (WHEN USING OPEN-COLLECTOR)
	POSITIONING FEEDBACK PULSE	ENCODER RESOLUTION: 22 BITS
	COMMAND PULSE MULTIPLYING FACTOR	ELECTRONIC GEAR A/B MULTIPLE, A: 1 TO 16777216, B: 1 TO 16777216, 1/10 < A/B < 4000
	POSITIONING COMPLETE WIDTH SETTING	0 PULSE TO ±65535 PULSES (COMMAND PULSE UNIT)
	ERROR EXCESSIVE	±3 ROTATIONS
	TORQUE LIMIT	SET BY PARAMETERS OR EXTERNAL ANALOG INPUT (0 V DC TO +10 V DC/MAXIMUM TORQUE)
SPEED CONTROL MODE	SPEED CONTROL RANGE	ANALOG SPEED COMMAND 1:2000, INTERNAL SPEED COMMAND 1:5000
	ANALOG SPEED COMMAND INPUT	0 V DC TO ±10 V DC/RATED SPEED (SPEED AT 10 V IS CHANGEABLE WITH
	SPEED FLUCTUATION RATE	±0.01% MAXIMUM (LOAD FLUCTUATION 0% TO 100%), 0% (POWER FLUCTUATION: ±10%) ±0.2%MAXIMUM(AMBIENT TEMPERATURE 25 ± 10 CENTIGRADE DEGREE) ONLY WHEN USING ANALOG SPEED COMMAND
	TORQUE LIMIT	SET BY PARAMETERS OR EXTERNAL ANALOG INPUT (0V DC TO +10 VDC/MAXIMUM TORQUE)
TORQUE CONTROL MODE	ANALOG TORQUE COMMAND INPUT	0VDCTO±8VDC/MAXIMUM TORQUE (INPUT IMPEDANCE: 10 TO 12 KOHM)
TORQUE CONTROL MODE	SPEED LIMIT	SET BY PARAMETERS OR EXTERNAL ANALOG INPUT (0VDC TO ± 10 VDC/RATED SPEED)
FULLY CLOSED LOOP CONTROL		AVAILABLE IN THE FUTURE
SAFETY FUNCTION		STO (IEC/EN 61800-5-2)
COMMUNICATION FUNCTION		USB: CONNECT A PERSONAL COMPUTER (MR CONFIGURATOR2 COMPATIBLE)
STRUCTURE (IP RATING)		FORCE COOLING, OPEN (IP20)
CLOSE MOUNTING		NOT POSSIBLE
WEIGHT (KG)		6.2