Mô tả sản phẩm
FR-F740-22K
Specifications
| Application of Inverter
Mitsubishi FR-F740-22K |
Fans, Pumps, HVAC |
| Power supply | 3P, 380 to 480Vac 50/60 Hz |
| Rated capacity | 22 kW |
| Rated current | 43 A |
| Output frequency range | 0.5 to 400 Hz |
| Starting Torque | 120% (3Hz) when set to simple magnetic flux vector control and slip compensation |
| Overload current rating | 120% 60s, 150% 3s (inverse time characteristics) |
| Control Method | V/f Control, V/f Control with PG, Open Loop Vector Control, Closed Loop Vector Control, Open Loop Vector Control for PM, Advanced Open Loop Vector Control for PM, Closed Loop Vector Control for PM |
| Braking unit | – |
| Input | Multi-speed selection, remote setting, second function selection, terminal 4 input selection, JOG operation selection, PID control valid terminal, external thermal input, PU-External operation switchover, V/F switchover, output stop, start self-holding selection, forward rotation, reverse rotation command, inverter reset, PU-NET operation switchover, External-NET operation switchover, command source switchover, inverter operation enable signal, and PU operation external interlock |
| Ouput | Inverter operation, up-to-frequency, overload alarm, output frequency detection, regenerative brake prealarm, electronic thermal relay function prealarm, inverter operation ready, output current detection, zero current detection, PID lower limit, PID upper limit, PID forward/reverse rotation output, fan alarm∗1, heatsink overheat pre-alarm, deceleration at an instantaneous power failure, PID control activated, PID output interruption, safety monitor output, safety monitor output 2, during retry, life alarm, current average value monitor, remote output, alarm output, fault output, fault output 3, and maintenance timer alarm |
| Protection Function | Overcurrent during acceleration, overcurrent during constant speed, overcurrent during deceleration, overvoltage during acceleration, overvoltage during constant speed, overvoltage during deceleration, inverter protection thermal operation, motor protection thermal operation, heatsink overheat, input phase loss ∗3 ∗4, output side earth (ground) fault overcurrent at start∗3, output phase loss, externalthermal relay operation ∗3, PTC thermistor operation∗3, parameter error, PU disconnection, retry count excess ∗3, CPU fault, brake transistor alarm, inrush resistance overheat, analog input error, stall prevention operation, output current detection value exceeded ∗3, safety circuit fault |
| Main Control Functions | Maximum/minimum frequency setting, frequency jump operation, external thermal relay input selection, automatic restart after instantaneous power failure operation, forward/reverse rotation prevention, remote setting, second function, multi-speed operation, regeneration avoidance, slip compensation, operation mode selection, offline auto tuning function, PID control, computer link operation (RS-485), Optimum excitation control, power failure stop, speed smoothing control, Modbus-RTU |
| Communication | PU connector
RS-485 |
| Peripheral Devices and Options | Parameter unit (8 languages), Enclosure surface operation panel, Parameter unit connection cable, AC reactor, DC reactor, EMC Directive compliant noise filter, EMC compliant EMC filter installation attachment, Radio noise filter, Line noise filter, Brake resistor, High-duty brake resistor, Brake unit, Resistor unit, Discharging resistor, Power regeneration common converter Stand-alone reactor dedicated for the FR-CV, High power factor converter, Manual controller, DC tach. Follower, Three speed selector, Motorized speed setter, Speed detector, Master controller, Soft starter, Deviation detector, Preamplifier, Pilot generator, Deviation sensor, Frequency setting potentiometer, Analog frequency meter, Calibration resistor, FR Configurator SW3(VFD setup software) |
| Degree of protection | IP 00 open -chassis, IP 20 NEMA Type 1 enclosure |
CÔNG TY CỔ PHẦN SX & TM PHẠM DƯƠNG
TRỤ SỞ: SN27, HẺM 201/12/20 ĐƯỜNG PHÚC LỢI, TỔ 6, P. PHÚC LỢI, Q. LONG BIÊN, HNOI.
MST: 0105176667
VPGD: SN 16/469, ĐƯỜNG NGUYỄN TRÃI, QUẬN THANH XUÂN, TP. HÀ NỘI.
TEL: 0485.854.668 FAX: 0462.852.262
HOTLINE: 0974 596 569 – 0945 627 188 – 0976 844 195 – 0968 627 188-0974090041
EMAIL: INFO@PHAMDUONGJSC.COM.VN – PHAMDUONGJSC@GMAIL.COM
WEBSITE: HTTP://PHAMDUONGJSC.COM.VN/ HTTP://PHAMDUONGJSC.COM/
WEBSITE: HTTP://SUNXVIETNAM.COM/ HTTP://TUDONGHOA365.COM/
WEBSITE: HTTP://CONGNGHIEPHOA.NET/
Đánh giá
Chưa có đánh giá nào.